Black Box IC821A serial converter/repeater/isolator RS-232 RS-422/485

Universal RS-232 to RS-422/485 Converter with optional Opto-Isolation

Key Features

• Convert RS-232 to 4-wire RS-422 or to 2- or 4-wire RS-485.
• Enable you to select RS-485 2-wire half-duplex or RS-485 4-wire full-duplex operation.
• Selectable RS-422 operation with transmit and receive always enabled.
• Automatic RS-485 driver control, so it works without any special programming for handshaking signals.
• No external power is required if two RS-232 output handshake lines are available.
• Universal RS-232 to RS-422/485 Converter
• Bidirectional data conversion.
• Enables transmitter from RS-232 TD signal and receiver when not transmitting.
• Set operating mode with four switches.
• Converts using either port power or power from an external 12VDC power supply (not included).

Description

Quick Facts

- Convert RS-232 to 4-wire RS-422 or to 2- or 4-wire RS-485.
- Features 2000-VAC isolation.
- RoHS compliant.
- Selectable RS-422 operation.
- Select RS-485 for 2-wire half-duplex or 4-wire full-duplex.
- Auto RS-485 driver control.

Further Details

The BLACK BOX® Universal RS-232 to RS-422/485 Converter with Opto-Isolation isolates and converts RS-232 signals into RS-422/RS-485 signals and vice versa. Unlike other converters, external software is not required to control data flow. The RS-232 input is wired for DCE through a DB9 female connector, and RS-422/RS-485 signals are interfaced through a removable terminal block. To supply external power to the terminal block, you need our 120-VAC/12-VDC Wallmount Power Supply (PS1003).

For RS-232, the connection requires RD, TD, and Signal Ground.

In RS-422 mode, the driver is always enabled for full-duplex communications. A twisted pair is required for transmit, and a twisted pair is also required for receive. A ground reference wire is also needed. Switch settings are Switch 1: RS-422; Switch 2: Echo On; Switches 3 and 4: 4 Wire.

In both RS-485 modes, the RS-485 driver is automatically enabled during each space state by the presence of an RS-232 signal. When the RS-232 data is in a mark or idle state, the RS-485 driver is disabled and the RS-485 data lines are held in a mark state by the bias provided by a 4.7-ohm resistor; the value of this resistor may need to be changed, depending on the termination you use.

To connect to several RS-485 devices with minimal wire, select the unit's 2-wire, half-duplex RS-485 mode. When data is requested, the addressed device transmits and then reverts back to receive status. Switch settings for this mode are Switch 1: RS-485; Switch 2: Echo Off; Switches 3 and 4: 2 Wire.

For 4-wire master/slave circuits, select the unit's 4-wire, full-duplex RS-485 mode. In this mode, addressed devices can receive data while transmitting data from a previous request. When used as a master in a single-master system, Switch 1 may be selected because the unit is the only transmitter in the system. When used as an RS-485 slave, the RS-232 device must provide addressability. Biasing in a master/slave system is provided by the end-of-line slave. Switch settings for this mode are Switch 1: RS-485; Switch 2: Echo On; Switches 3 and 4: 4 Wire.

NOTE: Power Supply (PS1003) is not included, but is required.

Specifications

Technical details
Serial ports quantity	2
Output interface	RS-422/485
Host interface	RS-232
Weight & dimensions
Dimensions (WxDxH)	0.906 x 3.9 x 1.69" (23 x 99 x 43 mm)
Power
Input voltage	10 - 48 V
Input current	0.028 A